Moen sells a tool that makes pulling cartridges easier, but sometimes you need more help than that. In less than ideal circumstances, however, the cartridge won't budge, no matter how hard you pull -- and you begin looking for ways to gain more leverage. Turn off the water source under the sink before you begin, though. Shut the water off, take the handle off and the ring under the handle that holds the cartridge in. If it is a shower faucet, do the same thing, just be sure you are careful and do not rip the shower valve out of the wall. It is either a cartridge or there will be a black rubber cup in the hole with a spring under… I assume the handles are the quarter turn type.
Check the flow of water to make sure that the hot- and cold-water adjustments work properly. Your kitchen faucet gets a lot of use, so you want to keep it in tip top shape. You need to remove the sleeve before you can insert a new cartridge. Step 4: Replace Cartridge Using the channel lock pliers, take out the old cartridge and replace it with the new one. You should press firmly to seat the washer almost flush with the bottom of the socket. Wipe a small amount of silicon grease onto the rubber washer. Carefully lift the sticker with a knife blade and remove the sticker.
The information presented here is for general educational purposes only. After turning off the water under the sink, remove the old cartridge. Back off open a little the handle, remove the cap nut the one the stem goes through that threads onto the faucet , this should do it. Remove it by unscrewing it. You must reinstall the new cartridge in exactly the same way. You may also have to gently pry the handle off. Looking for a quick fix? Therefore they are also expensive to replace 50 dollars for the valve, 150 dollars per shower valve if done by a competent plumber.
Removing a Kohler cartridge from a faucet is simply a matter of removing a few faucet parts so that you can gain access to the cartridge. In a single-handle faucet, the handle causes the internal cartridge to rise or lower within the faucet body to start and stop the flow of water. Remove the washer and set it aside as well. Some handles have setscrews on the side or rear. Stay connected with us on , , and! The faucet handle isn't the only thing between Richard and the cartridge; he must unscrew the bonnet——being careful not to scratch this chrome cover for the cartridge assembly—with a pair of slip-joint pliers. You'll need a swivel, optional size converter, and Teflon tape. The water shutoff is usually found directly under the sink and consists of a small valve and a small handle—one for the cold water pipe and one for the hot water.
In some cases you may see a retaining nut as soon as the handle has been removed. Note: This does not apply to ball type faucets. Single handle or double handle that quarter turn have a small rubber cup in them that wears out. Some faucets, like ours, have a gasket that goes between the sink and the faucet. Reinstall the faucet handle and setscrew or Phillips screw as well as the decorative cap, as applicable.
If it gets to the point that the pores of the fabric are clogged it needs to be replaced. There may be a decorative ring under the handle or not. First Step, if it is a… With the faucet shut off, take the handle off and under it is a nut around the stem. Also a couple of O rings to seal around the handle. Unscrew that and remove the stem and nut… You might want to replace your seats inside the body of the faucet. Do note you may have to turn two knobs to turn off the water completely: one for the hot water and another for the cold water. Unfortunately, these rubber parts often stick to the valve housing and make removing the cartridge a challenging job.
Loosen the cartridge retaining nut, using a pipe wrench or tongue-and-groove pliers. As the 1 faucet brand in North America, Moen offers a diverse selection of thoughtfully designed kitchen and bath faucets, showerheads, accessories, bath safety products, garbage disposals and kitchen sinks for residential and commercial applications each delivering the best possible combination of meaningful innovation, useful features, and lasting value. We just need a new one because the original ones in this house have been leaking a lot which increases our water bill. If everything works properly, replace the decorative cap and you're done. Most bathroom faucets that have two handles are cartridge-style faucets. Once the water is shut off, open the faucet fully to release any pressure in the water lines and let any water drain out.
Please note that your cartridge may have an imbedded cartridge nut. A new faucet is a great way to give a fresh look to a kitchen or bathroom. Secure the cartridge with the retaining nut, tightening the nut carefully do not over-tighten with the wrench or pliers. Usually, though, a single-handle cartridge faucet will give you the distinct sensation of the inner cartridge lifting upward when you turn the water on. Step 5: Reattach Faucet And Open Water Supply Place the faucet handle along with its screw and decorative cap back into place and open the water supply. If you have an imbedded cartridge nut and would like additional help, feel free to or call us for assistance at : Visit: for a step by step tutorial. Depending on the faucet you have, a repair kit which usually includes washers, o-rings, seats and springs or faucet cartridge can usually be found for most major name brands at your local hardware store.